![]() Be careful not to scratch, nick, or dent the bores that the jaws slide in or the jaws themselves. I used a combination of paper towels, pipe cleaners, an old toothbrush for the threads on the jaws, some 400 grit wet/dry sandpaper to remove some surface rust, and a small screwdriver to scrape away some thick grease. Once the sleeve is removed and bearings contained, remove the split nut and slide the jaws out of their bores. I used a magnetic parts tray under the vise to catch all the bearings that tried to escape. Use a suitable method of catching all of these tiny bearings. NOTE: there are a bunch of little tiny ball bearings inside this sleeve. With the jaws pointing downward, drive the chuck body out of the sleeve. Open the bench vise just wide enough so only the edges of the sleeve rest on the vise. ![]() 20 Volts : Amperage 1.5 Amps : Maximum Chuck Size 0. 1/4' Hex Chuck, 2 Batteries and Charger (DCF787C2). Unfortunately, the photo I took for this didn't turn out so I'll try to explain. Dewalt drill is compact at only 6.3 inch front to back designed to fit in tight spaces. This article explains the types, features, and terms necessary for purchasing a cordless power drill. Remove the flat washer, spring, and chuck collar. To get the jaws all the way out, there is a bearing race/sleeve that needs to be removed. This video explains how to carefully remove the transmissions of DeWALT drills and drivers, and how to replace them again. Use a pick and a small screwdriver to pry up one end of the retaining ring. Find a suitable replacement to fit your drill. The common threads on the drill are either 1/2-20 for 1/2" capacity chucks or 3/8-24 for 1/4" capacity chucks. If you need to replace the drill chuck, you can stop here and go buy a new chuck. Hopefully yours comes off much easier than mine did. Hold the drill firmly to the bench and hit the allen wrench downward using sharp blows with a hammer. Lay the drill down on it's side with the chuck hanging over the edge of a bench as pictured. Dirt and Debris Clean around the trigger thoroughly to remove any dirt and debris that may be blocking the trigger. Trigger Locked The trigger is stuck and will not give under pressure. ![]() The chuck will be a "lefty loosey" to remove. If the chuck is still unresponsive after thorough cleaning, you may need to replace your chuck. Once the screw is out, grab the largest allen wrench you have and tighten the short end into the chuck. This screw may possibly have a thread locker (locktite) on it - mine did. The normal saying "lefty loosey" is wrong when it comes to reverse threaded hardware. This means that to loosen the screw, you'll turn it to the right. Need help replacing the Motor (Part 396505-22SV) in your DeWALT Hammer Drill Watch this how to video with simple, step-by-step instructions for a successful. Mine was reverse threaded (left hand threaded), and most others will likely be reverse threaded as well. This could be any type of screw - phillips, allen, flat, star, hex, etc. Look into the bore of the chuck to see if there's a screw. Start by fully retracting the jaws into the chuck. Dewalt 18 Volt Battery (XRP, Ni-Cd) Obsolete - Not Available. Remember to use our power tool parts finder to find replacement parts for your impact drivers and other power tools.First step is to remove the chuck from the drill. This repair takes about 10 minutes and can be a life-saver if you get a bit stuck in your drill. ![]() Then use another screwdriver or your finger to finish seating the retaining ring.Ĭonclusion And that's how you can remove or replace the chuck on your impact driver. Use a screwdriver to snap one end of the retaining ring into place. Slide the collar into place and add the spring and flat washer. With the tension removed from the bearing, you can tap the driver on your work bench to remove a broken driver bit if that's why you removed the chuck. You do not have to remove this bearing, but be careful not to lose it. There is a ball bearing in the driver's anvil. Use a pick and a small screwdriver to pry up one end of the retaining ring. You can use our DeWalt parts finder to find chuck parts for your driver. This article shows you how to remove and re-install the chuck, allowing you to replace it or get at a stuck driver bit. If your chuck is worn or jammed, then you will need to remove and replace it. You may not need to replace the entire chuck in your impact driver, but if a bit breaks off inside of the chuck, you will need to remove the chuck.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |